General Specifications
- Components
- Thirty-two 50 mm (2 in) Full-Range Drivers
- Frequency Range (-10 dB)
- 80 Hz – 20 kHz
- Frequency Response (±3 dB)
- 130 Hz – 18 kHz (narrow coverage, music mode setting)
- Vertical Coverage (Narrow Mode)
- 15° (500 Hz – 16 kHz, +15°/-2° [<60° down to 220 Hz, <90° down to 140 Hz])
- Vertical Coverage (Broad Mode)
- 30° (400 Hz – 12 kHz, +15°/-8°, [<60° down to 220 Hz, < 90° down to 140 Hz])
- Vertical Coverage (Asymmetrical Progressive-Gradient Mode)
- (Top speaker module set at “Narrow” and bottom speaker module at “Broad”, for “J-type” coverage, sending higher sound levels toward the far area of the listening space) 22.°(+7° from aiming axis up; -15° from aiming axis down, 300 Hz – 12 kHz, +15°/-8°, [<60° down to 220 Hz, <90° down to 140 Hz])
- Horizontal Coverage
- 150° (ave, 1 kHz – 4 kHz, ±20°)
- Sensitivity – Narrow
- (Speech mode) 95 dB (2 kHz – 5 kHz) ; (Music mode) 92 dB (150 Hz – 18 kHz)
- Sensitivity – Broad
- (Speech mode) 93 dB (2 kHz – 5 kHz) ; (Music mode) 90 dB (150 Hz – 18 kHz)
- Sensitivity – Asymmetrical Progressive-Gradient Mode (on-axis)
- (Speech mode) 94 dB (2 kHz – 5 kHz) ; (Music mode) 91 dB (150 Hz – 18 kHz)
- Nominal Impedance (direct)
- 8Ω per half (top and bottom) for 4 ohms total (in thru mode). Min-Z for system = 2.9Ω.
- Hookup
- Ensure identical polarity of hookup – for proper functioning, the two loudspeaker modules (top and bottom) must be hooked up in same polarity. Parallel hookup at the two sets of back panel input terminals is recommended.
- Power Capacity (thru setting)
- 650W (2600W peak) ; 2 hrs 400W (1600W peak) 100 hrs
- Max SPL – Narrow
- (Speech mode) 123 dB cont ave (129 dB peak) ; (Music mode) 120 dB cont ave (126 dB peak)
- Max SPL – Broad
- (Speech mode) 121 dB cont ave (127 dB peak) ; (Music mode) 118 dB cont ave (124 dB peak)
- Max SPL – Asymmetrical Progressive-Gradient Mode (on-axis)
- (Speech mode) 122 dB cont ave (128 dB peak) ; (Music mode) 119 dB cont ave (125 dB peak)
- 70V/100V Transformer Type
- Set individually per speaker module (top and bottom) 120W, 60W, 30W (15W at 70V only), and direct 8Ω, via switch. Total (with top & bottom set to same) 240W, 120W, 60W (30W at 70V only) and direct 4Ω. Max. insertion loss less than 1 dB at any tap.
- Connectors
- Two (one for top half and one for bottom half), screw-down terminal strip, zinc-plated copper base, nickel plated metal screws/washers. Accepts up to 9 mm outside 4 mm inside open lug (#6, #8 or #10 lug), or bare wire (up to 12 AWC/2.5 mm2)
- Outdoor Capability
- IP-55 rated, per IEC529, when installed with optional MTC-PC2 panel cover. UV, moisture and 200-hr ASTM G85 acid-air/salt-spray resistant.
- Configuration
- Two pieces (top and bottom half), each 100 cm tall, connected together via Coupler Plate. Top/bottom orientation of each piece must be observed.
- Insert Points
- 28 M6 insert points on back panel (36 total with 8 center points being utilized by the Coupler Plate).
- Mounting
- Included swivel (pan) / tilt wall bracket (must be mounted to threaded points on Coupler Plate) provides continuously variable ±80° left-right swivel aiming (at up to ±5° up/down tilt), continuously adjustable ±10° up/down tilt, as well as 5° fixed increment tilt angles to ±10°. Twenty-eight available threaded mounting points (M6 diameter x M1 thread pitch x 17 mm deep) located on back panel. Threaded mounting points can be utilized for suspension. Compatible with OmniMount 30.0 brackets
- Included Accessories
- Swivel (pan) / tilt wall bracket, Coupler plate
- Optional Accessories
- MTC-PC2 terminal panel cover ; MTC-CBT-FM1 flush-mount low-profile wall-mount bracket (2 pieces required) ; MTC-CBT-SMB1 stand-mount bracket for use with 35 mm speaker stands (heavy duty stand required)
Dimensions
- Height
- 2000 mm (78.8 in)
- Width
- 98.5 mm (3.8 in)
- Depth
- 153 mm (6.0 in)
- Net Weight
- 14.6 kg (33 lb)
